杭州AG亞遊登陸地址動力科技有限公司主營:導電滑環,360度旋轉導電裝置,導電滑環結構圖,防水導電滑環,氣液電組合滑環,電旋!

新聞中心

  • 液壓滑環工作原理
  • 本站編輯:杭州AG亞遊登陸地址動力科技有限公司發布日期:2019-11-23 21:40 瀏覽次數:

液壓滑環,組成部分有1、一個底座。2、一個固定在底座上的芯軸。3、至少一個以上通過軸承安裝在芯軸上並能在芯軸上轉動的滑環體。4、還有若幹個設置在芯軸表麵與滑環體內表麵之間的密封件。5、在芯軸外圓柱麵上間隔設有多條配油環,內部設有若幹個相互不貫通並分別與不同的配油環相通的含有進油口的配油管路。6、在滑環體上也設有至少一個以上的與芯軸表麵不同的配油環連通的出油接口。

The hydraulic slip ring is composed of 1 and 1 base. 2. A mandrel fixed on the base. 3. At least one slip ring body which is installed on the mandrel through bearing and can rotate on the mandrel. 4. There are also several seals arranged between the surface of the mandrel and the internal surface of the slip ring. 5. A plurality of oil distribution rings are arranged at intervals on the cylindrical surface outside the mandrel, and a plurality of oil distribution pipes with oil inlet which are not connected with each other and are respectively connected with different oil distribution rings are arranged inside. 6. The slip ring body is also provided with at least one oil outlet interface communicated with the oil distribution ring which is different from the surface of the mandrel.

        采用以下進一步的技術方案在芯軸外圓柱麵上間隔地開有密封溝槽,密封件安裝在這些密封溝槽內。由於其本身的結構特點,它也可以承載一定的軸向力。同時液壓滑環本身還是一個自平衡元件。

Adopt the following further technical scheme to open sealing grooves on the outer cylindrical surface of the mandrel at intervals, and the seals are installed in these sealing grooves. Because of its own structural characteristics, it can also bear certain axial force. At the same time, the hydraulic slip ring itself is a self balancing element.

液壓滑環原理是什麽呢?

What is the principle of hydraulic slip ring?

2-1F526092543.jpg

1、單獨使用時,它把壓力油從液壓動力卡盤的外殼(固定不動)引入到旋轉油缸中去,使活塞在壓力油的作用下克服彈簧力以及阻力向右運動,帶動楔塊驅動卡爪鬆開工件。回程時,可以去掉壓力油的作用,靠彈簧複位作用,帶動滑軸驅動卡爪徑向卡緊工件。

1. When it is used alone, it introduces pressure oil from the shell of hydraulic power chuck (fixed) into the rotary oil cylinder, which makes the piston move to the right against the spring force and resistance under the action of pressure oil, and drives the wedge block to drive the claw to release the workpiece. During the return trip, the pressure oil can be removed, and the sliding shaft is driven to drive the claw to clamp the workpiece radially by the spring return function.

2、聯合使用時,將兩滑環組合使用。當回轉油缸左腔進油,右腔出油的時候,活塞杆向右運動,帶動楔塊驅動卡爪鬆開工件。當回轉油缸右腔進油,左腔出油的時候,活塞杆向左運動,帶動滑軸驅動卡爪徑向卡緊工件。

2. In case of joint use, the two slip rings shall be used in combination. When the oil enters the left cavity of the rotary cylinder and exits the right cavity, the piston rod moves to the right to drive the wedge to drive the claw to release the workpiece. When the oil enters the right chamber of the rotary cylinder and exits the left chamber, the piston rod moves to the left, driving the sliding shaft to drive the claw to clamp the workpiece radially.


AG电竞 AG8游戏平台 AG平台下载 AG亚游客户端下载 亚游游戏 d88尊龙AG旗舰厅手机版 AG摆脱游戏